![]() ![]() The Bluetooth Low Energy (BLE) integration scans for advertisement packets that other devices, like iBeacon or Bluetooth tags, emit. You can use any of the many different BLE tags or smart armbands out there, as long as they send out a constant ID. In order to re-enter normal operational model, simply remove and replace power to the device. An example would be the RadBeacon Chip open in new window or the iB001W open in new window. Select the DFU button to reboot the beacon into Direct Firmware Update mode.Ĭontact Radius Networks support for information on the procedure for firmware update or replacement. In order to re-enter configurable mode for a RadBeacon X2, remove the front cover and switch the beacon power switch to OFF and back to ON.Ī beacon set in configurable mode will be configurable for up to 30 minutes or until you lock the device again. In order to re-enter configurable mode for a RadBeacon Tag, remove the front cover and press the configuration push button switch near the coin cell battery. In order to re-enter configurable mode for a RadBeacon USB, remove and restore power to the device. The Lock feature is a security precaution to limit the possibility of third party manipulation of your beacons once they have been installed and configured. Select the Lock button to submit a valid PIN to prevent connections from remote Bluetooth 4.0 devices to the beacon configuration service. Submit a valid PIN to reset the settings for your beacon to factory defaults. Select the Reset button to reset the device to the original factory settings. Select the Update PIN button to submit a new and existing PIN to update the PIN for your beacon. Advertised Organizational Identifier Ĭhange any of the modifiable settings and select the Apply button to submit a valid PIN to update the settings for this beacon. Select any RadBeacon in the table to view it's detailed settings. Each beacon discovered is displayed with the following summary details The RadBeacon Dot Eddystone beacon can be configured to advertise iBeacon/AltBeacon and either Eddystone UID or Eddystone URL. Scan for nearby configurable RadBeacons by pressing the Start Scanning button. The RadBeacon USB Eddystone beacon can be configured to advertise any combination of iBeacon, AltBeacon, Eddystone UID, and Eddystone URL (although you must choose at least one). Once discovered, you can display each beacon's operating settings and make modifications to those settings. With the RadBeacon app you can scan for nearby configurable Radius Networks beacons. The RadBeacon app from Radius Networks requires a Macintosh computer running OS X 10.9 or higher and equipped with Bluetooth 4.0 capabilities. ![]() First make sure you beacons are in configurable mode.The RadBeacon™ app is the configuration utility for RadBeacon proximity beacons from Radius Networks that support Apple's iBeacon™ proximity services as well as other emerging proximity services. For details see "How do I put beacons into configurable mode?" This can be done by power cycling the beacon. In order to start scanning for beacons, first launch the RadBeacon configuration app. The main beacon scan screen is displayed which should be empty. ![]() To start scanning for beacons, press the SCAN button in the upper right corner on the action bar. This scans for beacons for 5 seconds and displays all beacons found during the scan. Potentially configurable Eddystone RadBeacons should be identified in the list with the Bluetooth device name "RadBeacon G". Tap on the beacon you would like to configure. If it is configurable, then the configuration detail screen for the beacon is displayed. If it is not configurable, an alert is displayed after 15 seconds indicating that the beacon could not be contacted for configuration. Occasionally, a configurable beacon cannot be contacted by the app on the first attempt, so you may need to try again. The RadBeacon USB Eddystone beacon can be configured to advertise any combination of iBeacon, AltBeacon, Eddystone UID, and Eddystone URL (although you must choose at least one). If you configure a URL to be broadcast, then it will broadcast iBeacon/AltBeacon and Eddystone URL. If you leave the URL blank, then it will broadcast iBeacon/Altbeacon and Eddystone UID. RadBeacon app, 24 configuring, 24-26 hardware, 20 Radius Networks. The Eddystone namespace ID cannot be entered directly in the RadBeacon configuration app. 46 retail applications mobile advertisement, 7 store enhancement, 7 transaction. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |